Видео

Can't get mine to line up

Preciodeunayabedwtrwsoctabos

You made that look so easy 😅, Thank you

So was it cranking and not starting

👍👍👍👍

My thing is, everywhere I see it working or not working, the stubby can fit. If it can bust brake caliper bolts, I don’t seee the point

Is no one going to mention the fact that he’s calling a Phillips screwdriver a flathead 😂

Bro that was a awesome video thanks for explaining and the camera work

music bangin

Your camera is all close-up shots, what wheel did you take off the passenger wheel or the driver side wheel? I took off the wheel on the driver side but there's no clip

Your a good young man. I hope and pray for great success for you, God bless

Currently day (4-10-24) Walmart has these for $21 maybe my set will be as good as yours

This is honestly easier than rebuilding a main Circuit board 😂 besides dropping the transmission part rebuilding automatic transmissions aren’t that hard

Second time I paid to replace it in 3 years. This time it was with the oil filter housing. $770 in just labor 😖.

trying to get mine back in, just wont go, rail just doesnt seem to twist enough to get that middle one in, it just drops into that cutout at the bottom easy enough but no matter how much leverage i put on that middle injector it wont move across to the hole. what am i doing wrong here? 3 hours and im getting tot he point of angle grinding part of the inlet runner off

How much does it cost with battery and charger?

Sweet teardown on that mfer..😂..interesting process , been years since I tore one down..old stuff..was wondering when I saw Milwaukee but then out came Infinium..✌nice work Davion..

👏👏👏👏

The snap on and or Mayhew are not made in the USA you’re doing a review and you don’t even have your facts straight

I will add, for the 3 screws in the fender skirts, it’s a 7/32 socket.

Thanks man, couldn't see the bolt so I was confused 🤣

Great video! Thanks!!

What the main failure points of this blowing like that? This just happened to mine in sports mode too

'promosm'

I tried to take off my cars lug nuts with my 1/2 inch right angle using the 2.5 amp battery, and it wouldn't work. I put on a 5 amp battery and it took it off with no problems as far as having move room with the smaller battery I guess that is correct but your hand is on the wrench so I don't think it would make that much of a difference but I'm sure in some situations it may. Thanks for the review.

Fantastic content 👌 👏 👍

Great video. I was wondering how to get some of the wires and hoses off of this pump it looks like a tight squeeze. I found an easy way to Route The Wires. I just cut the old electrical plug and when I rerouted the new one on the pump I didn't put it through the strap on the gas tank so I didn't have to loosen the strap at all I just put it in front of it using the clips that were included and it worked out perfect and was simple.

Did you have to remove transmission?

Nice video, interesting voltage drop test with a test light. I always use a multi meter. Good work.

Nice work Davion ✌🔧

Back at it I see 🔥🔥🔥

I don’t think is that weak

Nice Clip Tip....✌

Chip clip to the rescue

They have another hose that replaces the one that goes through the belt. So if making this repair it’s worth doing the hose replacement

Maybe don’t use impacts on a chrome socket? Get an impact bit holder.

Great diag, Thanks for sharing!

Good catch brotha. I love the multi use of the Dyvo meter.

Crankshaft and pig tail changed, back to no crank, no start after a few days of running. What can be the issue now?

Thank you for the video! I have a 2011 camaro 3.6. Can't get the P/side rail to clear the D/side cylinder head. Appears to be the same setup that you are working on. I have tried prying the rail to the back. Any help would be greatly appreciated. Identifix is saying to pull the cylinder head

My nikka

well done very clear and concise instructions. very thorough with everything. step by step instructions were very helpful. Thanks

Awesome tip thanks

Man thank you so much, I watched so many mf videos this the only one that really helped me get it done

🔥🔥

wat is the metal pipe going into thermostat houseing mine keeps poping out ????? how to pls help

Might want to update your upper hose so you don't have to screw with it again if you have to replace belt... F81Z-8260-CA Gets it around belt so you can just pop belt off and on. Lifesaver on the highway for when you eventually blow a belt.

Vi muchos videos pero este Es el mejor de todos.

😮. 3 CRANKS WAS ENUFF ,, NO NEED TO SMOKE THE STARTER ,,NOT GONA HEAL IT'S SELF 🤡

Yup. That’ll do